rattle can paint job tips

Start With a Tack Coat. Prep your cage well with sand paper scotch brite paint thinner ect.

Good Roller Paint Job Autoholics Owner Used Thinned Rustoleum 6 Coats And Buffing Car Painting Rustoleum Spray Paint Rustoleum

If you have access to a sand.

. Get that off now or youll be pissed later. For paint mottling youll need to wet sand by hand or machine - usually a high grit like 2000 3000 or 5000. Do the bed first overlap you coats of paint.

Use an aerosol clear. Wide spray nozzles is the way to go however and. What some of these finishes offer is a much thinner finish vs average rattle can paints.

Google rattle can your AR type or look up rattle can that shit on Facebook. If you find a 73 40 with fuel door upside down bezel and hard-top sporting Rustoleum Sand factory white fiberglass and grey primer for a roof liner that is likely. Dont underestimate the importance of good prep work.

9 Tips for Your Rattle Can Paint Job. Buy the paint in a quart can and shoot it with a cheap gun. I recommend disassembling your AR to the components you want to paint.

Harbor Frieght and Home Depot have cheap guns. Cover a panel at a time keeping the area wet with paint as you move along. Dont fret over mistakes and it is really better to under apply then to over apply.

To get the most out of the coating when the paint is dry to the touch in about 15 minutes give it a recoat. Rattle up the basecoat paint can ball bearing for at least a minute and then lay it down. After proper prep work and the proper environment to spray paint the key is uniform paint thickness mills achieved by one person doing the painting knowing basic painting techniques and following the manufacturers directions.

For best results hold it about 4-6 inches from your surface and spray in short bursts. Borrow or rent a small compressor. Do the prep right and youll have a nice low buck job thats easy to touch up.

If you have a scratch or divot you need to smooth it out before you paint or. Spray in a parallel line not a curved arc. Wear some kind of mask or respirator or youll be blowing paint out of your nose and lungs for awhile.

When you need to mix 2 part stuff you have to find that ratio that works best for you and stay with in that manufacture zone for it to cure right. I dont play with 2 part paints to often and I feel its probably temp sensitive also. Andy The best tip results I get from a rattle-can are to use the spray gun type of handles that attach to the top of the can.

Dont use rattle cans. For the overspray or dry spray you can fix by claying or using a clay substitute. You can see chipping its faded but held up well considering it cost about 50 to paint.

A tack coat is a light mist that you allow to set for five minutes. This will make the surface look professionally done. Spray Can Tips.

Rattle Can Tips I have been using Rustoleum spray paint for over 30 years now on a variety of projects from brackets to bicycles to bumpers to wheels to complete bodies and I have learned a couple of tricks along the way that I would like to share. The texture of the tack coat will help hold the paint in place and reduce runs. Ive seen some pretty nice rattle can paint jobs.

Most enamals can be thinned with acetone about 3 to 1 and shot without much expertise. If you hold your can more than 8-10 inches away you wont achieve the best finish. Stock will be pretty straight at this point.

For a good finish dont worry about wasting paint and make long even overlapping strokes. Set up a raking shop light and watch for the paint and solvent to level out together and hit the wet look. 14 Jul 14 2012.

Rattle can paint will NOT hide imperfections. A uniform coat is more important than an even coat. A can of this rattle paint can cover a wide area so you dont need to worry about it running out sooner than you expect.

You can also end up with mottling in the paint surface a kind of pebbled texture. Prime with spraymax 2k primer let dry a coupl days then block with your 150180 grit. For best paint job results and to avoid drips and runs move side to side and lay down several thin coats rather than one.

Rattle can mistakes often can be dealt with using acetone without damage to real paint. If you prepped your cage the night before there is going to be spider webs and all over it in the morning. I done it before but an air compressor and spray gun is so much easier and faster.

Start by getting ideas. In this video I am going to show you guys how you can paint your car using nothing but rattle cans well go over how to sand and fix scratches and scrapes. This is true on any paint job.

And something round 4-5 long for radius and barrel channel. The handles that snap on the rattle can helps a bunch. Ill usually start in a certain area like the lower driverside 14 and work my way up and over it gives you good coverage because your not trying to do the whole thing at once which is what leads to what I call Calico paint jobs you usually see.

Im gonna be painting it entirely again soon its certainly due but the point is rattle canning is in no way a bad decision. Start with 80grit and blocks I use lexan and acrylic sticks. I have seen guys spend hours taping off their AR.

Be smooth when you are sanding and dont use too much pressure as you dont want to create any deep scratches. About 1-buck each at Wal-Mart and they last forever. If youre spraying a vertical surface its always smart to apply a tack coat before applying the first full coat.

This paint is easily 10 years old minus the fenders and side vent painted those about a year ago. Youll be glad you did. After 80 grit switch to 150-180 grit.

I think it cost like 50-60 for paint and thinner from English color harbor fright gun for 12 and 100 for the air tank. While the cans I believe i used around 10 and they where about 5-7 each. Apr 29 2020.

Diy Paint Job Using Nothing But Rattle Cans Youtube